A
Alternating Current (AC)
The reversal of an electrical currents direction at regular intervals, adjustability controlled by an AC Frequency Control on Longevity AC TIG welders.
Amperage
The measurement of how much electricity flowing past a given point in a conductor per second. Current can be another name for amperage.
Arc
The gap between the end of the tip on the torch (on a plasma cutter or the electrode rod of a welder)/ and and the base metal. The physical gap causes heat from the resistance of current flow and the arc rays.
C
Current
Also known as amperage. The amount of electricity flowing past a given point in a conductor per second.
D
Defect
One or more impurities and/or flaws in a weld that cause a testing failure.
Dig
Also known as Arc Control. This gives a power source additional variable amperage during low voltage (short arc length) conditions while welding. This helps protect you from "sticking" your stick electrodes when a short arc length is used.
Direct Current (DC)
A current that flows in one direction and does not alternate its current path.
Direct Current Electrode Negative (DCEN)
(DCSP). The direction that the current flows through a welding circuit when the electrode lead is connected to the negative post and the work lead is connected to the positive post of a DC welding machine.
Direct Current Electrode Positive (DCEP)
(DCRP). The direction that the current flows through a welding circuit when the electrode lead is connected to a positive post and the work lead is connected to a negative post to a DC welding machine.
Duty Cycle
The percentage out a 10 minute time period that a welding machine can be ran at full amperage. Example would be 50% duty cycle at 60 amps. This would mean that at 60 amps the welding machine can be used for 5 minutes and then must be allowed to cool with the fan motor running for 5 minutes.
F
Flexible Automation
Automated robotically controlled welding system that can perform complex shapes and applications where the welding paths require torch-angle manipulation.
Flux Cored Arc Welding (FCAW)
An arc welding process which melts and joins metals by heating them with an arc between a continuous, consumable electrode wire and the work. Shielding is obtained from a flux contained within the electrode core. Added shielding may or may not be provided from externally supplied gas or gas mixture.
G
Gas Metal Arc Welding (GMAW)
Sometimes referred to by its subtypes metal inert gas (MIG) welding or metal active gas (MAG) welding, is a semi-automatic or automatic arc welding process in which a continuous and consumable wire electrode and a shielding gas are fed through a welding gun. A constant voltage, direct current power source is most commonly used with GMAW, but constant current systems, as well as alternating current, can be used. There are four primary methods of metal transfer in GMAW, called globular, short-circuiting, spray, and pulsed-spray, each of which has distinct properties and corresponding advantages and limitations.
Gas Tungsten Arc Welding (GTAW)
Also known as tungsten inert gas (TIG) welding, is an arc welding process that uses a non-consumable tungsten electrode to produce the weld. The weld area is protected from atmospheric contamination by a shielding gas (usually an inert gas such as argon), and a filler metal is normally used, though some welds, known as Autogenous welds, do not require it. A constant current welding supply produces energy which is conducted across the arc through a column of highly ionized gas and metal vapors known as a plasma.
Ground Connection
A safety connection from a welding machine frame to the earth. Please see work piece for the difference between your work connection and ground connection.
Ground Lead
Your ground wire connection that attaches from the machine to the work piece. Also known as the work lead.
H
Hertz
Hertz is often referred to as "cycles per second". In the United States, the frequency or directional change of alternating current is usually 60 hertz.
High Frequency
Covers the entire frequency spectrum above 50,000 Hz. Used in TIG welding and plasma cutting for arc ignition and stabilization.
I
Inverter
Power source which increases the frequency of the incoming primary power, thus providing for a smaller size machine and improved electrical characteristics for welding, such as faster response time and more control for pulse welding.
K KVA (Kilovolt-amperes)
Kilovolt-amperes. The total volts times amps divided by 1,000, demanded by a welding power source from the primary power furnished by the utility company.
KW (Kilowatts)
Primary KW is the actual power used by the power source when it is producing its rated output. Secondary KW is the actual power output of the welding power source. Kilowatts are found by taking volts x amps divided by 1,000 and taking into account any power factor.
M
Microprocessor
One or more integrated circuits that can be programmed with stored instructions to perform a variety of functions.
MIG Welding (GMAW or Gas Metal Arc Welding)
Welding process which joins metals by heating them with an arc. The arc is between a continuously fed filler metal (consumable) electrode and the work piece. Externally supplied gas or gas mixtures provide shielding.
There are four basic metal transfer modes:
Short Circuit Transfer - Name derives from the welding wire actually short circuiting (touching) the base metal many times per second. Some spatter is produced, but the transfer can be used in all welding positions and on all thicknesses of metal.
Globular Transfer - Named for "globs" of weld metal transferring across the arc in a gravity feed. Droplets across the arc are usually larger than the electrode diameter. It does not produce a very smooth weld bead appearance, and some spatter can occur. Usually limited to the flat and horizontal welding positions, and not used on thin metals.
Spray Transfer - Named for a "spray" of tiny molten droplets across the arc, usually smaller than the wire diameter. Uses relatively high voltage and amperage values, and the arc is "on" at all times after the arc is established. Very little if any spatter is produced. Usually used on thicker metals in the flat or horizontal welding positions.
Pulsed-Spray Transfer - For this variation of spray transfer, the welding machine "pulses" the output between high peak currents and low background currents. The weld pool gets to cool slightly during the background cycle, making it slightly different than Spray Transfer. This can allow for welding in all positions on either thin or thick metals.
O
Open-Circuit Voltage (OCV)
As the name implies, no current is flowing in the circuit because the circuit is open. The voltage is impressed upon the circuit, however, so that when the circuit is completed, the current will flow immediately.
P
Pilot Arc Automatic Restart
Automatically restarts the pilot arc when cutting through expanded metal or multiple pieces of metal, without having to re-press the trigger. This is included on our ForceCut LP-60I IGBT Plasma Cutter and our Weldall PI line of IGBT machines. Plasma Arc Cutting
An arc cutting process which cuts through metal by using a constricted arc to melt a small area of the work. This process can cut all metals that conduct electricity.
Pounds Per Square Inch (psi)
A measurement equal to a mass or weight applied to one square inch of surface area.
Power Efficiency
How well an electrical machine uses the incoming electrical power.
Power Factor Correction Normally used on single-phase, constant current power sources, to reduce the amount of primary amperage demanded from the power company while welding.
Primary Power
Often referred to as the input line voltage and amperage available to the welding machine from the shop's main power line. Often expressed in watts or kilowatts (KW), primary input power is AC and may be single-phase or three-phase.
Pulsed MIG (MIG-P) A modified spray transfer process that produces no spatter because the wire does not touch the weld puddle. Applications best suited for pulsed MIG are those currently using the short circuit transfer method for welding steel, 14 gauge (1.8 mm) and up.
Pulsed TIG (TIG-P)
A modified TIG process appropriate for welding thinner materials.
Pulsing
Sequencing and controlling the amount of current, the frequency, and the duration of the welding arc.
R
Rated Load
The amperage and voltage the power source is designed to produce for a given specific duty cycle period.
Resistance Spot Welding (RSW)
A process in which two pieces of metal are joined by passing current between electrodes positioned on opposite sides of the pieces to be welded. There is no arc with this process.
RMS (Root Mean Square)
The "effective" values of measured AC voltage or amperage. RMS equals 0.707 times the maximum, or peak value.
S
Semiautomatic Welding
The equipment controls only the electrode wire feeding. The welding gun movement is controlled by hand.
Shielded Metal Arc Welding
A manual arc welding process that uses a consumable electrode coated in flux to lay the weld. An electric current, in the form of either alternating current or direct current from a welding power supply, is used to form an electric arc between the electrode and the metals to be joined.
Shielding Gas
Protective gas used to prevent atmospheric contamination of the weld pool.
Single-Phase Circuit
An electrical circuit producing only one alternating cycle within a 360 degree time span.
Spatte
The metal particles that are blown away from the welding arc, which are not part of the completed weld.
Spot Welding
Spot welding is used on materials having some type of overlapping joint design. Can refer to resistance, MIG or TIG spot welding. Resistance spot welds are created from electrodes on both sides of the joint, while TIG and MIG spots are made from one side only.
Stick Welding (SMAW or Shielded Metal Arc)
Arc welding process which melts and joins metals by heating them with an arc, between a covered metal electrode and the work. Shielding gas is obtained from the electrodes' outer coating, often called flux. Filler metal is primarily obtained from the electrode core.
Submerged Arc Welding (SAW)
A process by which metals are joined by an arc or arcs between a bare metal electrode or electrodes and the work. Shielding is supplied by a granular, fusible material usually brought to the work from a flux hopper.
T
Three-Phase Circuit
An electrical circuit delivering three cycles within a 360 degree time span, and the cycles are 120 electrical degrees apart.
TIG Welding (GTAW or Gas Tungsten Arc)
Often called TIG welding (Tungsten Inert Gas), this welding process joins metals by heating them with a tungsten electrode which should not become part of the completed weld. Filler metal is sometimes used and argon inert gas or inert gas mixtures are used for shielding.
Trigger Reset
Permits quick reset at gun rather than at machine.
Touch Start
A low-voltage, low-amperage arc starting procedure for TIG (GTAW). The tungsten is touched to the workpiece; when the tungsten is lifted from the workpiece an arc is established.
Tungsten
Rare metallic element with extremely high melting point (3410 degrees Celsius).
V
Voltage
The pressure or force that pushes the electrons through a conductor. Voltage does not flow, but causes amperage or current to flow. Voltage is sometimes termed electromotive force (EMF) or difference in potential.
Voltage-Sensing Wire Feeder
Feeder operates from arc voltage generated by welding power source.
Volt-Amp Curve
Graph that shows the output characteristics of a welding power source. Shows voltage and amperage capabilities of a specific machine.
W
Weld Metal
The electrode and base metal that was melted while welding was taking place. This forms the welding bead.
Weld Transfer
Method by which metal is transferred from the wire to the molten puddle.
Wet-Stacking
Unburned fuel and engine oil collecting in the exhaust stack of a diesel engine, characterized by the exhaust stack being coated with a black, sticky, oily substance. The condition is caused by the engine being run at too light of a load for extended periods of time. Caught early, this does not cause permanent damage and can be alleviated if additional load is applied. If ignored, permanent damage can occur to the cylinder walls and piston rings.
Wire Feed Speed
Expressed in in/min or mm/s, and refers to the speed and amount of filler metal fed into a weld.
Workpiece Connection
A means to fasten the work lead (work cable) to the work (metal to be welded on). Also, the point at which this connection is made. One type of work connection is made with an adjustable clamp.
Workpiece Lead
The conductor cable or electrical conductor between the arc welding machine and the work.
-courtesty of Longevity
View this document in full at Clark Heintz Tools & Equipment's Website.
Friday, May 20, 2011
Thursday, May 19, 2011
What is an IGBT Plasma Cutter?
IGBT technology is a fairly recent invention. The first-generation devices of the 1980s and early 1990s were relatively slow in switching, and prone to failure through such modes as latchup and secondary breakdown. Second-generation devices were much improved, and the current third-generation ones are even better, with speed rivaling MOSFETs, along with extreme ruggedness and tolerance of overloads.
The extremely high pulse ratings of second- and third-generation devices also make them useful for generating large power pulses in areas like particle and plasma physics, where they are starting to supersede older devices like thyratrons and triggered spark gaps.
Their high pulse ratings, and low prices on the surplus market, also make them attractive to the high-voltage hobbyist for controlling large amounts of power to drive devices such as solid-state Tesla coils and coilguns.
Availability of affordable, reliable IGBTs is a key enabler for electric vehicles and hybrid cars. Toyota’s second generation hybrid Prius has a 50 kW IGBT inverter controlling two AC motor/generators connected to the DC battery pack.
Plasma Cutting Process
Plasma cutting, in a nutshell, is the process for cutting steel and metal of different sizes and thickness using a plasma torch. During the plasma cutting process, inert gas (or compressed air, as used in some machines) is ejected at high speed from the nozzle, while simultaneously, an electrical arc is made from the gas of nozzle to the surface to facilitate the cutting.
This plasma is hot enough in order to melt the cut metal, while also moving fast to blow the metal far from the present cut. Additionally, plasma arc cutters and several other applications also deploy the Insulated Gate Bipolar Transistor (IGBT) plasma cutting technology to provide more commercial plasma cutting equipment.
How IGBT Plasma Cutters Work
The IGBT plasma cutters are better suited for professional environments because they adopt a different method to start the pilot arc. Many IGBT plasma metal cutters often utilize high-frequency starting technology just for the starting process, while, conversely, others use Pilot Arc starting technology, where the torch enables a constant arc without touching your work.
The Insulated Gate Bipolar Transistor (IGBT) compared with the Metal Oxide Semi-conductor Field Effect Transistor (MOSFET) has been a controversial subject ever since the IGBT technology was developed in the 1980s.
While in the process of developing light weight inverter-based welders that use less power, there are many technologies to consider. Transistors are essential in creating the welding arc, as they serve as tiny micro switches that deliver power to the work electrode. There is a wealth of technical information available regarding the use as well as selection of these transistors and the suitability of each to different applications.
IGBT technology for welding applications is proven to effectively take care of the rigorous demands of the high-duty cycles welders because it offers higher heat tolerances and higher voltage capacities than the earlier MOSFET.
IGBT Plasma Cutting Technology
MOSFETs are not well-suited to handle the voltage pressure or extreme heat mounted on them by the industrial welding environs. While MOSFET is reasonable sufficient when powering lower-end welding equipment, they simply do not suffice in meeting the demands of heavy duty welding requirements.
Of course, MOSFET technology is still currently available but it is more limited. It is offered to customers as an economical alternative, in particular, for hobbyists and "part-time" enthusiasts. Now, however, the majority of manufacturers cater to the needs of the professional welder and the welding industry in general by mass-producing a line of IGBT based welding inverters.
It has to be admitted that for certain low-end welding applications, MOSFET technology has failed unable to cope up when pushed to limits. IGBT technology, on the other hand, has proved extremely capable of handling all types of work, however tough.
The transistors that were used most commonly at one time were MOSFET but in today's world things have changed; IGBT plasma cutters are the units favored in commercial and industrial applications where amperage demand is high. The IGBT plasma cutter may be more readily found in several high current plasma metal cutting machines that produce over 60amps of power.
There are several IGBT plasma cutters and welders lined up in the market and most of them are of high quality, easily portable, competitively priced and widely bought by professional welding operators. Among the state-of-the-art IGBT technology plasma cutters that we carry are the Longevity ForceCut 40i Plasma Cutter, the Longevity ForceCut 50i plasma cutter, Longevity ForceCut 60i plasma cutter, the Longevity ForceCut 80i plasma cutter, Longevity Weldmax 205i multipurpose plasma cutter /welder, and the Longevity Weldmax 250i multipurpose unit.
**Info for this article courtesy of Everlast Power Equipment Inc. and Wikipedia
The extremely high pulse ratings of second- and third-generation devices also make them useful for generating large power pulses in areas like particle and plasma physics, where they are starting to supersede older devices like thyratrons and triggered spark gaps.
Their high pulse ratings, and low prices on the surplus market, also make them attractive to the high-voltage hobbyist for controlling large amounts of power to drive devices such as solid-state Tesla coils and coilguns.
Availability of affordable, reliable IGBTs is a key enabler for electric vehicles and hybrid cars. Toyota’s second generation hybrid Prius has a 50 kW IGBT inverter controlling two AC motor/generators connected to the DC battery pack.
Plasma Cutting Process
Plasma cutting, in a nutshell, is the process for cutting steel and metal of different sizes and thickness using a plasma torch. During the plasma cutting process, inert gas (or compressed air, as used in some machines) is ejected at high speed from the nozzle, while simultaneously, an electrical arc is made from the gas of nozzle to the surface to facilitate the cutting.
This plasma is hot enough in order to melt the cut metal, while also moving fast to blow the metal far from the present cut. Additionally, plasma arc cutters and several other applications also deploy the Insulated Gate Bipolar Transistor (IGBT) plasma cutting technology to provide more commercial plasma cutting equipment.
How IGBT Plasma Cutters Work
The IGBT plasma cutters are better suited for professional environments because they adopt a different method to start the pilot arc. Many IGBT plasma metal cutters often utilize high-frequency starting technology just for the starting process, while, conversely, others use Pilot Arc starting technology, where the torch enables a constant arc without touching your work.
The Insulated Gate Bipolar Transistor (IGBT) compared with the Metal Oxide Semi-conductor Field Effect Transistor (MOSFET) has been a controversial subject ever since the IGBT technology was developed in the 1980s.
While in the process of developing light weight inverter-based welders that use less power, there are many technologies to consider. Transistors are essential in creating the welding arc, as they serve as tiny micro switches that deliver power to the work electrode. There is a wealth of technical information available regarding the use as well as selection of these transistors and the suitability of each to different applications.
IGBT technology for welding applications is proven to effectively take care of the rigorous demands of the high-duty cycles welders because it offers higher heat tolerances and higher voltage capacities than the earlier MOSFET.
IGBT Plasma Cutting Technology
MOSFETs are not well-suited to handle the voltage pressure or extreme heat mounted on them by the industrial welding environs. While MOSFET is reasonable sufficient when powering lower-end welding equipment, they simply do not suffice in meeting the demands of heavy duty welding requirements.
Of course, MOSFET technology is still currently available but it is more limited. It is offered to customers as an economical alternative, in particular, for hobbyists and "part-time" enthusiasts. Now, however, the majority of manufacturers cater to the needs of the professional welder and the welding industry in general by mass-producing a line of IGBT based welding inverters.
It has to be admitted that for certain low-end welding applications, MOSFET technology has failed unable to cope up when pushed to limits. IGBT technology, on the other hand, has proved extremely capable of handling all types of work, however tough.
The transistors that were used most commonly at one time were MOSFET but in today's world things have changed; IGBT plasma cutters are the units favored in commercial and industrial applications where amperage demand is high. The IGBT plasma cutter may be more readily found in several high current plasma metal cutting machines that produce over 60amps of power.
There are several IGBT plasma cutters and welders lined up in the market and most of them are of high quality, easily portable, competitively priced and widely bought by professional welding operators. Among the state-of-the-art IGBT technology plasma cutters that we carry are the Longevity ForceCut 40i Plasma Cutter, the Longevity ForceCut 50i plasma cutter, Longevity ForceCut 60i plasma cutter, the Longevity ForceCut 80i plasma cutter, Longevity Weldmax 205i multipurpose plasma cutter /welder, and the Longevity Weldmax 250i multipurpose unit.
**Info for this article courtesy of Everlast Power Equipment Inc. and Wikipedia
Subscribe to:
Posts (Atom)